Betta Fish Care  
Go Back   Betta Fish and Betta Fish Care > Betta Fish Bowls, Habitats, and Accessories
Check out the eBook Betta Fish Care Made Easy
betta fish
Reply
 
Thread Tools Search this Thread
Old 01-16-2011, 12:50 PM   #1 
jschristian44
Member
 
jschristian44's Avatar
 
Join Date: Jan 2011
Step-By-Step Elite Mini c02 Diffuser

Hey guys,
So I've been reading up on c02 because I was planning on getting some sort of a planted tank. Anyways, I bought the Elite Mini Filter because it was cheap and looked like a great filter for my baby betta fry. It does do it's job very well, but is pretty strong. Still should work fine on the lowest setting. Anyways, I've been reading about supplying c02 to my plants and saw a youtube video on how this filter could be used as a c02 diffuser. I am thinking about getting another one because they are cheap and just putting them side by side in the tank. Anyways, I finally figured out how to do this. Here are the steps and a link for the Elite Mini. This credit goes to --Nikolay on APC site. I just thought since so many have been talking about c02 here on BettaFish.com I would post this. Note: You still need to make the DIY yeast bottle diffuser to put the tubing from this reactor into. This isn't a complete setup. Just google how to make the DIY yeast bottle diffuser, there are tons of sites out there on how to do it. But overall, you can get a good c02 setup for your tank for under 20 dollars. People have said they used this setup on 40 gallons and less with good success.

In the box you will find everything needed to make an extremely efficent in-tank Co2 reactor:

1. Discard the tubing that supplies air to the filter and is meant for aeration, you don't need it.
2. Open the filter - as if your intention is to clean the sponge.
3. Remove the sponge from the compartment.
4. Pull and remove the green flow control slider.This leaves a small opening on the side of the filter.
5. Close the filter without the sponge. When doing that put the CO2 tubing in the small opening mentioned above. Basically 1/2" of the CO2 tubing is now inside the filter, right under the intake, and it's held in place by the closed filter.
6. The filter comes with a flow nozzle. Put the sponge removed in step 3 over this nozzle.
7. Attach the flow nozzle to the filter.
8. Peel off the technical info sticker. It's white and attracts the eyes.
9. Done!

Basically you have done two things:
A. Put the CO2 tubing under the intake of the filter.
B. Attached the sponge on the outtake of the filter.

When the filter runs the CO2 bubbles hit the pump impeller and make a very gentle noise. This is your bubble counter. Count the bubbles with your eyes closed if you want. You will have to get about a foot from the reactor though - it's hard to hear if you are more than 2-3 ft. away.

When the bubles hit the impeller they get broken into tinier bubbles. These tiny bubbles then get trapped in the sponge with 60 gph of water flow disolving them almost 100%.

The few fine bubbles that escape the sponge look like a tiny cloud. It consists of bubbles so fine that they have a hard time floating up to the surface. Even the most gentle side flow carries them to the side and around the plant leaves.

Old design of mine but this $10 filter really makes it possible to make an ideal internal CO2 reactor in literally less than 1 minute. The filter is very small (easy to hide), black (doesn't attract the eyes), and has a strainer that makes the suction gentle enough so snails don't get stuck on the intake, die and block it. Virtually zero maintenance.
jschristian44 is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Step-By-Step Filter Baffle Kim Betta Fish Bowls, Habitats, and Accessories 281 08-08-2014 06:10 AM
DIVIDING TUTORIAL, step-by-step with pics Neelie Betta Fish Bowls, Habitats, and Accessories 92 11-21-2013 07:44 PM
STEP-BY-STEP water changing 2.5g WITH PICS Neelie Betta Fish Bowls, Habitats, and Accessories 23 11-15-2011 12:46 PM
Can anyone help me step by step with the cycling? girls_interrupted Betta Fish Care 3 04-20-2008 10:30 AM


All times are GMT -5. The time now is 03:46 AM.


Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.